Invidia r400

[Tim818]

Second that. Mine was hanging bit low too when it was still up on the hoist, asked the mechanic and he adjusted the hangers, now it sits perfectly like stock's.

Mines sit slightly lower only because I don’t want the tips to burn the rear oem diffuser.

Sponsored

 

[SaiHayashi]

Mines sit slightly lower only because I don’t want the tips to burn the rear oem diffuser.

Good point for hanging em low too.

 

[Apex Carver]

Did some baseline pulls over the past week just to confirm the gains of this exhaust. Back to back pulls of a stock 2018 CTR vs. my 2018 with the R400 only (no other mods). Looks like 20.5 hp peak gain.

 

[CincyTypeR]

Did some baseline pulls over the past week just to confirm the gains of this exhaust. Back to back pulls of a stock 2018 CTR vs. my 2018 with the R400 only (no other mods). Looks like 20.5 hp peak gain.

Thanks for posting the results. Although would be more accurate if done on the same vehicle since not all engines are created equal. Some may be stronger or weaker and others. But at least gives general possible idea.

 

[Apex Carver]

Agreed, it would have been ideal to have it done on the same car before/after install but thats all the dyno time I could book for now.

In any case it falls in line with other plots i've seen for the exhaust/stock cars.

 

[VooDuuChild]

Thanks for posting the results. Although would be more accurate if done on the same vehicle since not all engines are created equal. Some may be stronger or weaker and others. But at least gives general possible idea.

Very true. There was a back to back on the same car earlier with a 23 hp gain. Back on page 13 I believe. Stands to reason, this dyno is pretty close also.

 

[jasonjm]

I looked away from this exhaust before the change in resonator, it looks huge and nice. I think this is back on my radar simply because of the price and that it might produce all the right sounds.

 

[Z06_Pilot]

I've had mine on for a few months now, and really like it. I do wish the fitment was a little better. The tips do not fit up nice and tight into the cove as I would like. I have seen pix of this exhaust where they do fit up in the cove like the OEM, and others that are like mine-hang about 3/4" lower than OEM. Had my installer put it up on a lift. It's not a hanger problem or anything like that. There is only about a 1/2" clearance of the pipe to the cutout between the rear suspension pieces, so it's not like they can just push up the mufflers and tips higher.

I think the manufacturing process is not consistent....

 

[jasonjm]

I've had mine on for a few months now, and really like it. I do wish the fitment was a little better. The tips do not fit up nice and tight into the cove as I would like. I have seen pix of this exhaust where they do fit up in the cove like the OEM, and others that are like mine-hang about 3/4" lower than OEM. Had my installer put it up on a lift. It's not a hanger problem or anything like that. There is only about a 1/2" clearance of the pipe to the cutout between the rear suspension pieces, so it's not like they can just push up the mufflers and tips higher.

I think the manufacturing process is not consistent....

Is there drone in the cabin?

 

[Apex Carver]

Is there drone in the cabin?

Yep there sure is... its pretty bad around highway speeds at around 3000 rpms

 

[jasonjm]

Yep there sure is... its pretty bad around highway speeds at around 3000 rpms

Oh that sux

 

[JSmoothBui]

Sound clip with the new resonator, help out a lot with cabin drone.

Which resonator did you replace the Invidia one with?

 

[Kami Speed]

Anyone interested in a full titanium version? Just got word that they're working on that right now!

 

[Ghostype_R]

Anyone interested in a full titanium version? Just got word that they're working on that right now!

Have any pricing ?

 

[Kami Speed]

Going to be selling for $3150, but shoot me a message and I'll see if I can get you a good deal to test it out!

Sponsored