Time Attack
Motion Control Suspension 2-ways, 900lbs front 1300lbs rear springs, RV6 sphericals front and rear, Karcepts rear bar full stiff, stock front bar
-3.2 front -.1 toe out
-2.4 rear +.1 toe in
295/30/18 front, 265/35/18 rear Advan A052
lowered to front arms fairly level, 3/4" rake...
We sent the motor to 4 Piston Racing for rebuild back in 2018, so we had the built block before we upgraded the turbo setup. However, 4 Piston found our block seemed to be defective from factory.
I have only seen claimed data showing poor IAT's from the Mishimoto intake, but our hours and hours of recorded data on and off track in GA high ambient temps have not shown high heat soak of the mishimoto intake nor poor IAT, this on a car that has track data at multiple power levels from...
Nine Lives Racing also has one, they are more affordable option, aluminum, but full CFD design and work well on track. Original design was done on out Time Attack CTR, first one here on first FK8 to compete in Honda Challenge, built by us as well. 2 length options, 3 end plate options, gurny...
Racebred sells the splitter precut specifically for the CTR, in different sizes up to 3". This one was done special in 4", thats 4" extension. I used 2 of their s2000 quick release mounts, slightly modified, but still not easy to release on CTR, doing it again i would use custom bolted...
We have some vents sets being cut right now, our own design. We 3D scanned the hood top and bottom to fit the vents perfectly, and used CAD airflow data for design. Ours are primarily designed for true track enthusiasts and have a panel that replaces the stock scoop, as well as 3 other panels...
2021 Civic Type R will be the limited edition, so we know that 2021 will still be 10th gen, but most likely the Limited Edition will close out the generation and mid 2021 we will see the 12th Gen come as a 2022 model
Racebred Components splitter using their s2000 quick release chassis mounts modified to fit the CTR bumper support beam, 4 support braces behind the bumper. works very well, is very stiff. Very happy with it.
I am putting together a "Race" BBK with Wilwood. It will be a Race spec but will also be fine for street. It is similar to the Honda Performance Development setup that is used on the World Challenge TCA class Civic Si race cars, that kit is exclusively available from HPD for actual race cars...
I have been running these parts, as well as the rear trailing arm sphericals for nearly 2 years on our time attack FK8, including many miles on the street. I personally feel they don't hamper the ride quality enough to offset the performance advantage. If you are deciding on a spherical joint...
I didnt read all the comments, but anyone that says the dash gauge is enough, sure, it is enough for basic street driving but if you are tracking the car, I recommend having a real numerical value present. The stock gauge is slow to react until actual temps get dangerously high. I have seen...
we honestly didnt see that in our testing originally, but our enviroment wasnt as controlled as theirs may have been. Currently we are using the Mishimoto maint box unit but with a custom top panel to clear our larger 4" MAF Housing
I have one of these new DD-R Exhaust on the way for my Si Coupe build. I will install it and get clips with stock DP and front pipe, then with the RV6 Catless DP and front pipe
USR race side mount oil cooler, 25 row
USR 3" stainless race exhaust with single exit Magnaflow muffler
USR 4-Point hard mounted mini hoop harness bar
USR front tow hook
USR front spherical sway bar drop links
USR custom radiator ducting
USR strut brace with brake master cylinder support
4...
The Godspeed arms use Spherical bearings on both ends so they will move some once tightened down. Just make sure the jam nuts on the outboard adjustment are tight.
Did you actually try it? I have bolted OEM FK8 fenders on an FK7 hatch. The lower takes some working of the sideskirt or use CTR side skirts, but otherwise the fender bolts right on. I have a 2018 Si coupe and we have some FK8 carbon fenders at the shop that I will be installing on it, so I...