Hi all,
I wish to replace my MAP sensors and I am not sure if I can just buy it online and swap it by myself or do I need to do some calibration on the sensor themselves?
sorry for the noob question
Didn’t noticed before you mentioned it. I think it might make me return then lower ball joints from spoon. I’ll stick with a smaller turning radius and not mess with the knuckles
Can anyone advise on this?
Are 51211-TGG-A01(51216-TGG-A01) and 51211-TET-H00(51216-TET-H00) interchangeable for all models?
i purchased 51220-FK7-010(Spoon's Ball Joint) and it doesn't fit into my front knuckles
https://www.blackhawkjapan.com/products/spoon-51220-fk7-010
i believe i have...
Thanks man! I just measured mine 13.5 inches in front and 13 inches at the rear! Now I know how much my car is lowered. I actually measured before I changed to coilovers but I couldn’t remember the lengths
Nice! I am looking for a similar setup but i am lowered on coilovers
Could you help a fellow Civic guy our and measure the the length from from wheel fenders to the center wheel cap for both front and rear wheels? are they 13.5 inches or 14.5 inches or a different length?
What are you Wheels offset, Tires spec? Are you lowered? Do you get any rubbing without any wheel spacers or fender mod?
I am looking to get 17x9 ET+49 with 245/45/r17 and i am being told by the local shops it might rub..
Thank GT, i was wanting to wait for the intake Manifold + Throttle body upgrade later this year to do it, but i guess i am going have to do it again after that update again. For local tuner here, i have no idea what software they use and i hate to see my K-Tuner become useless...
UPDATE #2
Vehicle: Civic Hatchback 2017 CVT with paddle shifters (Known as FK4 in Asia and Australia)
Total tuned time: About 24 months
Tuned miles driven: Tuned 50,000km(31,000 miles), Total 136,000km(84,500 miles)
Tuning device(s) used: K-Tuner v1.2
Tunes used: K-Tuner’s Dual Starter 21...
Can i check if anyone who still has 2017-2021 Hatchback with Stock Suspension + Springs(Not lowered), what is the length from the very center wheel hub cap to the fender?
I recently had my 2017 Hatchback lowered on Tein's Street Advance and i now measure 13.5 inch at the front and 13 inch at...
Hello, you have Tein Street Advance Z? I have that now and the ride height is so low! i am gonna change to 17"x9" + 49ET with 245/45r17, will i run into rubbing issues with this setup with the Tiens coilovers? Any advise is appreciated!
Question: Do i do the braces before or after the Spoon Collars?
Hi Guys, i decided to get Ultra Racing Front and Middle Member Brace instead of Cusco Power Braces because the Cusco doesn't fit FK4(Holes but no bolts), i will be installing the Spoon Rigid Collars(Front and Rear) at the about...
Hey Mo-Mo,
After doing some research. The hose I circled is the PCV breather hose and it’s totally NOT normal that it’s like this. If yours is like this, look to get it replaced ASAP
17131-59B-010 PCV Hose
17130-59B-003 PCV valve(replace this and hose again if after replacing the Hose the same...
Yes! i have a gauge to tell the CVT temps and before it got above 212F+ fast! Now, the max is about 170-185F even with hard driving, the only drawback is that my ECT will up about 5F+
Could it be a vacuum leak/issue? Does this look normal?
I will be changing my low pressure fuel pump + fuel lines in 1-2 weeks, so that would eliminate one possible factor but i doubt it would solve the crazy jerk in hot weather
Unfortunately i would not be touching the Manifold(Skunk 2?)...
Hey, do you happen to stay in a place with hot and humid climate? i notice that mine jerks like crazy on hot days when i am in stop/go traffic and my a/c is on...
Still trying to find the exact cause..
Thanks everyone for confirming fitment, getting these in and likely install it end of this month or early next month together with new turbo back exhaust and Intercooler + pipes