- Joined
- Jan 26, 2017
- Threads
- 113
- Messages
- 1,575
- Reaction score
- 4,325
- Location
- Export, PA
- Website
- prlmotorsports.com
- Vehicle(s)
- 2017 Civic Si, 2016 Civic EX-T, 2018 Type R
- Thread starter
- #1
Pulled from the PRL Army Blog
PRL Motorsports 2017+ Honda Civic Type-R FK8 High Volume Intake System Install Guide
Install Time: 1 Hour
Disclaimer:
Table of Contents:
Tools Needed:
Air Box Preparation:
Loosely install velocity stack into cone filter
Place the loosely attached air filter and velocity stack assembly into the air box. Rotate the band clamp so that the screw is easily accessible in the air box.
Attach the MAF housing to the velocity stack by aligning the holes through the air box with the (4) socket head cap screw bolts. Torque bolts to 11.2 in/lbs or until snug.
Loosely attach the air box lid with 8 of the 10 button head cap screw bolts, carefully working your way from one side of the box to the other.
Once all bolts are placed through the air box lid's holes, tighten to 24 in/lb or until very snug. (Blue Loctite is not a bad idea either)
Loosely attach the air box bracket with the flat tab facing down using the remaining 2 of the 10 button head cap screw bolts. Leave these bolts loose so that the bracket can slide from side to side for optimal fitment.
PRL Motorsports 2017+ Honda Civic Type-R FK8 High Volume Intake System Install Guide
Install Time: 1 Hour
Disclaimer:
- Install was performed on a modified application. Some hardware shown may be different than the hardware used on the stock
- vehicle.
- Allow vehicle to cool completely prior to attempting installation.
- PRL Motorsports is not responsible for any vehicle damage or personal injury due to installation errors, misuse, or removal of PRL Motorsports products.
- PRL Motorsports suggests trained professional installation all PRL Motorsports products
Table of Contents:
- (1) Air Box
- (1) Air Box Lid
- (10) M5 x 0.80 x 10mm Button Head Cap Screw for Air Box Lid
- (1) Billet Aluminum MAF Housing
- (1) Billet Aluminum Velocity Stack
- (1) Oiled Cone Filter
- (1) Silicone Inlet Hose
- (1) #52 Stainless Steel Worm Clamp
- (1) #44 Stainless Steel Worm Clamp
- (1) #20 Stainless Steel Worm Clamp
- (1) #8 Stainless Steel Worm Clamp
- (1) Stainless Steel Air Box Bracket
- (1) Billet Aluminum Evap Bung
- (1) 12" Convoluted Tubing
- (4) M6 x 1.00 x 16mm Socket Head Cap Screw for MAF Housing to Velocity Stack
- (2) M4 x 0.70 x 8mm Socket Head Cap Screw for MAF Sensor
Tools Needed:
- Ratchet
- Extension (12" Length)
- 10mm Socket
- Flathead Screwdriver
- Phillips Screwdriver
- 3mm Hex Allen Key
- 5mm Hex Allen Key
- Electrical Tape
Air Box Preparation:
Loosely install velocity stack into cone filter
Place the loosely attached air filter and velocity stack assembly into the air box. Rotate the band clamp so that the screw is easily accessible in the air box.
Attach the MAF housing to the velocity stack by aligning the holes through the air box with the (4) socket head cap screw bolts. Torque bolts to 11.2 in/lbs or until snug.
Loosely attach the air box lid with 8 of the 10 button head cap screw bolts, carefully working your way from one side of the box to the other.
Once all bolts are placed through the air box lid's holes, tighten to 24 in/lb or until very snug. (Blue Loctite is not a bad idea either)
Loosely attach the air box bracket with the flat tab facing down using the remaining 2 of the 10 button head cap screw bolts. Leave these bolts loose so that the bracket can slide from side to side for optimal fitment.
Last edited: