KTuner Extended Testing And Tune Results

D-RobIMW · Mar 16, 2018

fk8mike said:
confused by this

That's how DynaPack expresses torque calculated after it divides the actual torque multiplied by the transmission by the drive ratio: FW Torque = actual applied torque to the hubs / (drive gear ratio x final drive ratio)

It is the figure at the hubs (wheels), not the engine. It's impossible to know that without an engine dyno that doesn't have the parasitic losses associated with the transmission, clutch, flywheel, axles, brakes, wheel bearings, etc.

Great power, @vanovem1 ! The torque differences in the run-to-run testing may be a result of some knock retard or from IAT's, or both. This ECU is pretty good at monitoring all of that and sticking power back in.

17CivicTypeR_Brian · Mar 16, 2018

Interesting- I made more torque but less hp. Probably differences in ambient temp and fuel.
Enjoy it!

vanovem1 · Mar 17, 2018

17CivicTypeR_Brian said:
Interesting- I made more torque but less hp. Probably differences in ambient temp and fuel.
Enjoy it!

I also have PRL Intercooler and Milltek exhaust. Not sure if you have any other mods. But between ambient temps, time between runs, different mods, probably makes some differences. It’s still fun! You enjoy also, can’t wait until we can meet up at C&C sometime

Raw 381 · Mar 17, 2018

vanovem1 said:
Ok so I have gotten KTuner v1.2 and just wanted to share my experience. Unfortunately it wasn't as simple for me as it was for most, but KTuner was constantly available to help solve the problem. My laptop was taking a little longer to flash the ECU than I think they had planned for, so mine was timing out and putting my ECU in recovery mode. As soon as KTuner extended the timeout threshold, sent me a new version, and I flashed...everything worked as advertised. So big thanks to KTuner getting it all fixed. Glad I could at least help this from happening to someone else.

I flashed with the Stage 1 multi tune, and WOW. The throttle and turbo response is unreal. The power is so smooth throughout the range in 3rd through 6th. I was spinning quite a bit in 1st, so I am going to add some torque dampening to this tune. 2nd gear did not spin as much as I thought it would...still some spin though. I think the Hasport 62A rear mount helped out alot! I also have a PRL Intercooler and Milltek Sport Road+ exhaust and Acuity shifter base bushings. I am absolutely loving this tune. It put out 343 hp and 352 lb ft torque. The torque seems just a little inconsistent in the mid-range, and I let KTuner know my experience to see what they think. What do y'all think? Heres my dyno graph (dotted line was baseline with no mods...100% stock). I definitely 100% recommend the KTuner for our car!

Thanks for the info!! Just curious was this on 93 octane?? Wondering what this tune will do on 91 since that’s all we have here in Cali

KTuner · Mar 17, 2018

Raw 381 said:
Thanks for the info!! Just curious was this on 93 octane?? Wondering what this tune will do on 91 since that’s all we have here in Cali

He was on 93 for sure. 91 results are slightly lower and will depend on the fuel quality, of course!

vanovem1 · Mar 17, 2018

Raw 381 said:
Thanks for the info!! Just curious was this on 93 octane?? Wondering what this tune will do on 91 since that’s all we have here in Cali

Yup KTuner is right. I was on 93 Ocatne Sunoco fuel

KTuner · Mar 17, 2018

vanovem1 said:
Yup KTuner is right. I was on 93 Ocatne Sunoco fuel

Lucky. We're stuck with 91 here too.

fk8mike · Mar 17, 2018

KTuner said:
Lucky. We're stuck with 91 here too.

same issue here,,only shell vpower so i was looking to the torco octane booster to help a bit,or watermeth spray..but im not sure about that.. so what the difference in whp vs the 93??(i mean approx) 30whp?

mdela0880 · Mar 20, 2018

KTuner said:
Lucky. We're stuck with 91 here too.

Is there any update yet @KTuner as to when the V2 flash is expected to be available again as it’s already been two weeks since it was announced that there were manufacturing issues? Thanks!

KTuner · Mar 20, 2018

mdela0880 said:
Is there any update yet @KTuner as to when the V2 flash is expected to be available again as it’s already been two weeks since it was announced that there were manufacturing issues? Thanks!

Yup, couldn't have happened at a worse time for us and may have been due to a regulation change on chemicals used. They're still fighting to get the vat back to the quality they expect. We may offer some uncoated as blasted aluminum (Still looks good) for those who do not want to wait, but they will scratch easier and take on fingerprints. Whether we do that depends on feedback from you guys.

lawl · Mar 20, 2018

KTuner said:
Yup, couldn't have happened at a worse time for us and may have been due to a regulation change on chemicals used. They're still fighting to get the vat back to the quality they expect. We may offer some uncoated as blasted aluminum (Still looks good) for those who do not want to wait, but they will scratch easier and take on fingerprints. Whether we do that depends on feedback from you guys.

hahah these people are so impatient they'd probably be okay with it wrapped in blue tape if it meant they could get it earlier.

but a silicone condom could probably work?

mdela0880 · Mar 20, 2018

KTuner said:
Yup, couldn't have happened at a worse time for us and may have been due to a regulation change on chemicals used. They're still fighting to get the vat back to the quality they expect. We may offer some uncoated as blasted aluminum (Still looks good) for those who do not want to wait, but they will scratch easier and take on fingerprints. Whether we do that depends on feedback from you guys.

I’ve orderered myV2 almost two weeks ago and I can only speak for myself but I don’t care to much about the casing or fingerprints. I simply want to get one whether it looks like how they used to or the blasted aluminum. Either way works for me. I simply want to get the production rolling so I can get my V2 regardless of what case it comes with honestly @KTuner

KTuner · Mar 20, 2018

lawl said:
hahah these people are so impatient they'd probably be okay with it wrapped in blue tape if it meant they could get it earlier.

but a silicone condom could probably work?

You may be right. That would obstruct the view of the LCD!

mdela0880 said:
I’ve orderered myV2 almost two weeks ago and I can only speak for myself but I don’t care to much about the casing or fingerprints. I simply want to get one whether it looks like how they used to or the blasted aluminum. Either way works for me. I simply want to get the production rolling so I can get my V2 regardless of what case it comes with honestly @KTuner

We are waiting for samples... but if they aren't perfect I'll offer the blasted aluminum to anyone who's currently on back order. Stay tuned for an update!

lawl · Mar 20, 2018

KTuner said:
You may be right. That would obstruct the view of the LCD!

We are waiting for samples... but if they aren't perfect I'll offer the blasted aluminum to anyone who's currently on back order. Stay tuned for an update!

well i guess like a phone silicone case rather than... an actual condom

KTuner · Mar 20, 2018

lawl said:
well i guess like a phone silicone case rather than... an actual condom

If they can be made, I'm sure.

KTuner Extended Testing And Tune Results

D-RobIMW

www.imwtuned.com

17CivicTypeR_Brian

Aiming for 400whp out of the TypeR.

vanovem1

Senior Member

Raw 381

Senior Member

KTuner

vanovem1

Senior Member

KTuner

fk8mike

Senior Member

mdela0880

Member

KTuner

lawl

Senior Member

mdela0880

Member

KTuner

lawl

Senior Member

KTuner

Similar threads