US and ASEAN OEM Accessorised 2016 Civic

[CosmicTouring]

What about your low/high beam bulbs, I assume you swapped them out with something as well?

I have a Touring and they are already LEDs

Sponsored

 

[CosmicTouring]

Super nice man! Can you tell me where to get the chrome tailpipe tips? I also am wondering where you found the civic door sill plates. You're the ONLY person I've seen who has either of these and I have been trying to find them for months. Thanks! 2016 civic touring coupe wop.

Bought both on ebay from seller Riennakane....thanks

 

[skittles]

Update 5/6/16: Completed my accessories. Included added accessories to the list and added new pictures.

I am almost done with my cosmetic mods using US and ASEAN OEM accessories. Last thing is the clear sidemarkers. Just wanted to share some pics for those that may be interested in accessories. To each their own.

I have the MGP caliper cover and Honda valve stem caps as non-OEM accessories.

Full mod list:

Exterior:

US:
Door Edge Chrome
Front, Side and Rear Underbody Spoiler
Clear door edge film
MGP Caliper Covers
Honda Valve Stem Caps
Weathertech Clear Cover License Plate Frames (front and back)

ASEAN OEM:
Fog Light Chrome Trim
Exhaust Tips
Clear Sidemarkers
Chrome Fender Garnish

Interior:
US:
OEM Footwell Illumination
OEM Console Illumination
Husky Weatherbeater Floor Mats
Honda OEM Trunk Tray
Weathertech Cargotech
Photodon MXH Infotainment Screen Protector

ASEAN OEM:
Aluminum Pedals
Non-Illuminated Door Sill Trims

Tint:
Llumar CTX Ceramic Air 80 Windshield
Llumar CTX Ceramic 35 Front
Llumar CTX Ceramic 15 Rear and Sunroof

Lights:
3rd brake light: Sylvania Zevo 7440R
L/R brake light: Philips Vision LED 7440 Red
Reverse light: Philips White Vision LED 921
Fog Light: Philips X-tremeVision LED Fog Lamp H8/H11/H16 - 2 Pack (12834UNIX2)
Interior Light: exLED Honda Civic, '13~ (Map, Dome, Trunk, License Plate) - you won't need the license plate lights. These are exact fit LEDS that fit the entire housing.
Side marker light: Sylvania 194A LED

Looks sharp...

 

[Javex]

It is OEM so it is literally plug and play. The exhaust tip has a pipe leading to the finisher that is the exact shape and bend as the muffler pipe. There are also 3 tabs inside the finisher pipe that stops the muffler pipe when inserted. Slide the exhaust tip on the muffler pipe until you reach the 3 tabs. It will be pretty tight already after this. For added safety there is a large clamp that has a bolt that needs to be tightened to close the clamp and fully secure the tip. All done. No aligning needed.

Your car looks great. The chrome works awesome with that color. The only exterior thing I would change is the side molding but that's just my preference. I am new here and I've been reading and reading... I think your car exhaust tips are the first ones I like and feel they look a bit "natural". Pretty hard to pull off since the car has them hidden.

I would like to get those for my car. I love cars but I am not very handy.... was that complicated to do? I read what you said and it seems like a noob like me could do it. Is there any special prep or anything else you need to do? or is it just add, bolt, secure, admire and tap yourself on the back?

Thanks in advance!

 

[CosmicTouring]

Your car looks great. The chrome works awesome with that color. The only exterior thing I would change is the side molding but that's just my preference. I am new here and I've been reading and reading... I think your car exhaust tips are the first ones I like and feel they look a bit "natural". Pretty hard to pull off since the car has them hidden.

I would like to get those for my car. I love cars but I am not very handy.... was that complicated to do? I read what you said and it seems like a noob like me could do it. Is there any special prep or anything else you need to do? or is it just add, bolt, secure, admire and tap yourself on the back?

Thanks in advance!

Thanks for the compliment. You got it right with the install. Just make sure you push the tip all the way until the exhaust pioe hits the 3 small tabs inside the tip.

 

[Javex]

Thanks for the compliment. You got it right with the install. Just make sure you push the tip all the way until the exhaust pioe hits the 3 small tabs inside the tip.

Thank you very much.

Last question.... I live in Canada... this wont rust right?

The item is out of stock and I just got the car... I will keep this in mind for future purchases. This forum is not good for my wallet. LOL

 

[CosmicTouring]

Thank you very much.

Last question.... I live in Canada... this wont rust right?

The item is out of stock and I just got the car... I will keep this in mind for future purchases. This forum is not good for my wallet. LOL

Lol....it should last awhile since it is OEM

 

[jan_se07]

Hey man (@CosmicTouring)!

I almost have the same accessories from the ASEAN version but I don't know how to install the fog light chrome garnish - it's been sitting in my room for 2 months because of this. How were you able to install them? Do you have an instruction manual or paper that can guide me or my dealership on how to install them?

Your help and advice would be greatly appreciated.

 

[CosmicTouring]

Hey man (@CosmicTouring)!

I almost have the same accessories from the ASEAN version but I don't know how to install the fog light chrome garnish - it's been sitting in my room for 2 months because of this. How were you able to install them? Do you have an instruction manual or paper that can guide me or my dealership on how to install them?

Your help and advice would be greatly appreciated.

Sorry....no guide...just profit and it almost lines up itself. Just trip the small stabs, line up, stick and pull off remaining tape backing.

 

[jan_se07]

Sorry....no guide...just profit and it almost lines up itself. Just trip the small stabs, line up, stick and pull off remaining tape backing.

Thanks for replying. I can see screw holes in the back of the item where the tape backing is, so did you drill through your fog light housing too?

 

[CosmicTouring]

Thanks for replying. I can see screw holes in the back of the item where the tape backing is, so did you drill through your fog light housing too?

No. I trimmed those tabs so it is flat. You mount with just the adhesive tape.

 

[johnyeah183]

your car looks awesome!

found this Chinese OEM pedals, the gas pedal looks like a fit for our version unlike the Thailand version. is there anyway to confirm?
http://www.ebay.com/itm/GENUINE-HON...efefe89&pid=100005&rk=1&rkt=6&sd=322048386277


AND, how you installed the pedals? drilling required?

 

[CosmicTouring]

your car looks awesome!

found this Chinese OEM pedals, the gas pedal looks like a fit for our version unlike the Thailand version. is there anyway to confirm?
http://www.ebay.com/itm/GENUINE-HONDA-ACCESS-OEM-SPORT-AUTO-PEDALS-10TH-GEN-CIVIC-SEDAN-COUPE-2016-2017/121991527360?_trksid=p2047675.c100005.m1851&_trkparms=aid=222007&algo=SIC.MBE&ao=1&asc=20131003132420&meid=d118043541a945dfba0ed36f1efefe89&pid=100005&rk=1&rkt=6&sd=322048386277


AND, how you installed the pedals? drilling required?

Not sure how you can confirm without having on hand. There is drilling needed on the gas pedal. They mount with rivets.

 

[Andy123az]

Can you link me to those door sill trims? They look really nice.

Is it possible that you take a photo/video of the third brake light in action? Does the whole bar light up evenly? Or is most of the light concentrated to where the light bulb is?

Thank you.

Sponsored