PRL Motorsports 2017+ Honda Civic Type-R FK8 High Volume Intake System Install Guide

[fiend busa]

Thanks guys, my velocity stack was preinstalled into the cone when I got it so I think i must of missed it lol.

Is the velocity stack supposed to go inside the filter or just around it.

Edit: Yas after an hour and half I got the filter part installed LOL, not looking forward to hooking it up into the car

Sponsored

 

[boosted180sx]

Thanks guys, my velocity stack was preinstalled into the cone when I got it so I think i must of missed it lol.

Is the velocity stack supposed to go inside the filter or just around it.

Edit: Yas after an hour and half I got the filter part installed LOL, not looking forward to hooking it up into the car

Oh wait till you get to the silicone pipe and the purge valve lol

 

[fiend busa]

Oh wait till you get to the silicone pipe and the purge valve lol

 

[fiend busa]

Oh wait till you get to the silicone pipe and the purge valve lol

How'd you remove the screw from the clamps on the stock intake. They're so tight and head is getting damaged if I try to use a flat head

 

[fiend busa]

How did you guys remove this??
https://imgur.com/a/iSkEr65

All the heads on the clamps are also welded so theres no way to remove the screws with a flathead as well.

 

[TypeSiR]

How did you guys remove this??
https://imgur.com/a/iSkEr65

All the heads on the clamps are also welded so theres no way to remove the screws with a flathead as well.

https://www.civicx.com/threads/prl-...system-install-guide.39548/page-8#post-685691

 

[fiend busa]

https://www.civicx.com/threads/prl-...system-install-guide.39548/page-8#post-685691

Thanks dude, do you know how I can get the screws of the clams on each end off too? The washers are straight welded to the clamp lol

Actually I'm going to home depot and getting a dremel to cut these clamps off lol

 

[J35W2]

Thanks dude, do you know how I can get the screws of the clams on each end off too? The washers are straight welded to the clamp lol

Actually I'm going to home depot and getting a dremel to cut these clamps off lol

Good call. Dremel really is a must have. It has fixed many problems for me that would have been WAY tougher without. The diamond cutting wheel is expensive, but will easily cut just about anything (including porcelain tiles!)

 

[fiend busa]

One after another more problems lol

I used a dremel cut the clamps but now the next problem is the dam screws on the maf sensor, they're so tight that using a flat head just shreds the head

Any tips?

 

[boosted180sx]

One after another more problems lol

I used a dremel cut the clamps but now the next problem is the dam screws on the maf sensor, they're so tight that using a flat head just shreds the head

Any tips?

i was able to take it off easily. I used a ratchet with a screwdriver bit

 

[fiend busa]

i was able to take it off easily. I used a ratchet with a screwdriver bit

Got it to work.

Next to the battery was a 10mm screw, pro intake doesnt reach it when I connect to the grommet. Is it supposed to just not go in?

When the grommet goes in, the back side is too high for the 10mm to go all the way down to the chassis screw.

And the box wont go down any further

 

[boosted180sx]

Got it to work.

Next to the battery was a 10mm screw, pro intake doesnt reach it when I connect to the grommet. Is it supposed to just not go in?

When the grommet goes in, the back side is too high for the 10mm to go all the way down to the chassis screw.

And the box wont go down any further

what do you mean. I left everything loose and was not an issue.

 

[fiend busa]

what do you mean. I left everything loose and was not an issue.

This

https://i.imgur.com/Uxo4cfF.jpg

 

[fiend busa]

Cant fit tube wont go down

https://i.imgur.com/Mf86RGi.jpg

 

[boosted180sx]

it should fit without issues. have all the bolts loose. i had to kinda guide the bottom grommet into the pink by reaching under it

Sponsored