BREMBO UPGRADE ON MY SPORT HATCH

Green82

Senior Member
Joined
Nov 5, 2017
Threads
51
Messages
848
Reaction score
292
Location
Oklahoma
Vehicle(s)
2019 Type R
Vehicle Showcase
1
Country flag
They wouldn't fit over the Brembos without excessive spacers, pushing the wheels out too far from the car.
Ahh thanks . Yea don' want the wheels to stick out since I want to lower it a bit for a better stance
Sponsored

 

DTAM_Sa

Family is everything
First Name
DAVID
Joined
Feb 4, 2018
Threads
1
Messages
9
Reaction score
5
Location
San Antonio
Vehicle(s)
2018 Si Sedan
Are you running stock rotors or are they s2000?
 

88_driver

New Member
First Name
jim
Joined
Oct 23, 2017
Threads
0
Messages
2
Reaction score
1
Location
nyc
Vehicle(s)
2017 fk7, 2001 ap1
is there any modification needed to mount these calipers? like any milling of the mounting brackets. i assume trimming of the backing plate is required to run this
 

Doublestack00

Senior Member
Joined
Nov 12, 2016
Threads
46
Messages
887
Reaction score
512
Location
GA
Vehicle(s)
2020 Boost Blue Type R
Vehicle Showcase
2
Country flag
What is needed to run these calipers/rotors?
 


brun

Member
Joined
Aug 9, 2017
Threads
0
Messages
45
Reaction score
43
Location
Richmond, TX
Vehicle(s)
'17 ABM CTR #358, '01 2JZ-GTE IS300, '08 TW FA5, '15 WDP MDX SH-AWD ENT
Country flag
looks awesome! good work
 

Boosted_01_R

Senior Member
Joined
Jul 17, 2016
Threads
34
Messages
524
Reaction score
351
Location
Canada
Vehicle(s)
2020 FC3
Country flag
You would have to check brake line ports/length etc, its the small things what will get ya, so I can't confirm that's all you need... It's one of those things, I'm looking at DC5 wilwood 4pot kit for my 01ITR. Wilwood said its been done, cut can't officially say so. Couple of washers, on the caliper could made the difference.

For the 10th gen, the S2K rotor is much easier to find than a DC5R rotor and I assume has the proper offset for the caliper. I haven't done it so I can't confirm 100%

If your not tracking you car, 100% waste of time conversion, but does look cool... Brake balance would be off, some will says its fine. I would get proportion valve, and bias a little more to the rear after the conversion. Just my 2 cents, PM those who has done it.
 

bobvudown

Senior Member
First Name
bob
Joined
Mar 13, 2018
Threads
5
Messages
58
Reaction score
9
Location
Las Vegas
Vehicle(s)
2018 Civic Si coupe
Country flag
Since you’re using S2k rotors, can I get the dc5r or s2k Spoon calipers and mount those on the car?
 


hikaru

Senior Member
First Name
Shawn
Joined
Mar 18, 2018
Threads
15
Messages
1,016
Reaction score
586
Location
Marietta
Vehicle(s)
2018 Civic Sedan 1.5T, 2009 Accord Sedan 2.4 LX-P, 2000 Civic Sedan EK4
Vehicle Showcase
1
Country flag
Just wanna share my brembo kit swap

20171219_123735.jpg


20171116_231402.jpg


received_10155360899499032.jpeg
I know this is an old thread, but I just wanted to know if spacers are needed for DC5 brembo to go with the stock Si/Sport wheels?
 
OP
OP
MetalKnightCivicHB
Joined
May 23, 2017
Threads
55
Messages
971
Reaction score
475
Location
Chicago
Vehicle(s)
17 civic hb sport
Vehicle Showcase
1
Country flag
I know this is an old thread, but I just wanted to know if spacers are needed for DC5 brembo to go with the stock Si/Sport wheels?
yea at least 20mm spacers if using the stock wheels
 

hikaru

Senior Member
First Name
Shawn
Joined
Mar 18, 2018
Threads
15
Messages
1,016
Reaction score
586
Location
Marietta
Vehicle(s)
2018 Civic Sedan 1.5T, 2009 Accord Sedan 2.4 LX-P, 2000 Civic Sedan EK4
Vehicle Showcase
1
Country flag
OP
OP
MetalKnightCivicHB
Joined
May 23, 2017
Threads
55
Messages
971
Reaction score
475
Location
Chicago
Vehicle(s)
17 civic hb sport
Vehicle Showcase
1
Country flag
Thanks, that's what I wanted to know. Any wheel vibration with the spacers added?
When I had spacers on, i didnt feel any vibrations at all. Even drove it at 90 mph no problem. Just torque it properly
 


 


Top