anyone know what the part number for front bottom heat shield flat head turnlock fasterner ?

[cataclysmseng]

hi all. my front bottom cover screw is missing. anyone know whats the parts number. i want to purchase. there is 6 of them

 

[NeoDragons]

hi all. my front bottom cover screw is missing. anyone know whats the parts number. i want to purchase. there is 6 of them

. i am also missing one screw but unfortunalty in Honda genius engineering, they dont sell those half turn screws seperatly. you would have to purchase the entire engine cover along with the black plastic piece it contects to just to get those screws. which is about 80 bucks online

 

[HayaiKuruma]

^ Yes, this is the 3rd or 4th thread asking this question. We all want to know.

 

[cataclysmseng]

. i am also missing one screw but unfortunalty in Honda genius engineering, they dont sell those half turn screws seperatly. you would have to purchase the entire engine cover along with the black plastic piece it contects to just to get those screws. which is about 80 bucks online

omg... any other solution...the screw look like this

 

[NeoDragons]

omg... any other solution...the screw look like this

yup thats the one.

 

[HayaiKuruma]

Everyone needs to call Honda and report that this part is not available seperately, even for dealers. Call 800-999-1009 and hit option #7 (I think). Explain the situation. The dude said if they get enough reports about this something will be done. Tell them it should be included on the parts diagram on Honda estore, etc.

 

[HayaiKuruma]

Looks like Honda borrowed the idea from VW/Audi.

https://www.aliexpress.com/item/10p...07692536.html?spm=2114.search0302.4.75.QRNfV1

https://www.aliexpress.com/item/x10...8037091.html?spm=2114.search0302.4.102.toNi0B

 

[Bob60506]

Did anyone find these parts? My low mileage 2016 Accord uses them, too. I'm about to replace them all with some Philips head sheet metal screws. I really HATE doing it, as I'm a staunch OE kind of owner, but this was a truly crappy design. Even with careful alignment of the connectors' wings with the slots in the sheet metal clips, I can't even get most of them to bite into the clips the way they're supposed to, thus causing damage to the slots in the "screw" heads. Who thought of designing a screw with such a long, wide slot that's only half as deep as it is wide? Criminy. Yet another engineer who hasn't a clue about building or repairing a car...

 

[adrian8m]

Does anyone know the part number for the whole metal part?
Mine fell off on the freeway.

 

[ApexProxy]

Check out 90674-TY2-A01

 

[Bru87tr]

If you bring your car to a quick oil change place, they are prob to blame. Mine were, they only put 4 back in and keep rest so its easier to take off next time around. My plate fell off and got mangled, was easy enough to fix with a rubber hammer. But made them pay for my missing screws.

https://rover.ebay.com/rover/0/0/0?mpre=https://www.ebay.com/ulk/itm/401558169158

 

[ronny]

Well, there you go.

 

[Myx]

Just read this post. May as well add whatever I find...
Part Number: 91512-SX0-003
CLIP, TRIM (7MM) *NH167L* Part Number: 90667-S0D-003ZH



I'll keep looking for that underpanel piece.

 

[julianzh]

Just read this post. May as well add whatever I find...
Part Number: 91512-SX0-003
CLIP, TRIM (7MM) *NH167L* Part Number: 90667-S0D-003ZH



I'll keep looking for that underpanel piece.

You mean this one?

https://m.aliexpress.com/item/32949...3g_QY_d0voAp4eDUJTg2TVB98bpVplJX1563388395613

Sponsored