Search results

  1. RV6 R660 RED Ball Bearing Turbocharger

    Dang I should've painted it too. I'm running both and wrapped my cerakoted DP. Looks pretty OEM.
  2. RV6 R660 RED Ball Bearing Turbocharger

    Well, it's finally all bolted up and yeah the PTP blanket fit. Can't wait to get it dialed in with Derek!
  3. RV6 R660 RED Ball Bearing Turbocharger

    Did the PTP blanket fit on the r660?
  4. Strange creaking noise of front suspension?

    How did this go for you guys? Suddenly my FK8 has been doing this on full lock while turning the wheel to park from a stop.
  5. RV6 R660 RED Ball Bearing Turbocharger

    Sounds good man thanks for that! just want to make sure.. I mean it says non-silicate/borate so I guess that's the main thing? Or valvoline zerex.. idk if I'm gonna make a mess might as well flush it I feel like. Yeah for US/Canada.. Our honda's are all red too, and I see the states the...
  6. RV6 R660 RED Ball Bearing Turbocharger

    Ahh makes sense. Do your bottles look like the ones in the pic? or are they the grey bottled ones? Maybe it's a Honda US vs Canada thing 🤷‍♂️ this apparently the only coolant the dealership has (black bottle). Have to pay attention for the hoses for sure. Feel like I'm studying for an exam...
  7. RV6 R660 RED Ball Bearing Turbocharger

    Hot tip man thanks for that. Took a peek at their instructions. Pretty much just helps keep track of things. For the coolant, what do most people replace with? Do people just run OEM Type 2? I looked online and most of the ones I found are the old grey ones.. but when I went to the parts dept...
  8. Wasgate Calibration on FK8

    Were you able to fix the issue?
  9. RV6 R660 RED Ball Bearing Turbocharger

    Thanks for the info @ebatr24 . That's what I expected but wasn't sure! Did you use the safety wire as well? How messy was it in your experience with the coolant? I've done all the bolt ons on the car myself but this is the first time taking stuff of that can actually.. leak/spray on me lol so...
  10. RV6 R660 RED Ball Bearing Turbocharger

    Makes sense. Will keep a note for that. Would you say similar to how we shouldn't be going super tight on the drain nut or oil filter? Just trying to make sure I don't go back and forth changing things. Also, noticed the kit comes with 4x stud/washer/nut. Is there a preferred installation...
  11. RV6 R660 RED Ball Bearing Turbocharger

    I'm in the same boat. All my parts have arrived awaiting pickup at the border and will be taking note of things when installing. EDIT: his video asks an important question for people who are about to install this. How tight are we supposed to actually get that AN line down?
  12. RV6 R660 RED Ball Bearing Turbocharger

    Hi @RV6 , I know it was mentioned for oil specs in the thread, but for someone who drives the car up to as low as 5-10C, adding the R660 is the recommendation still to use 5w-30 oil?
  13. RV6 R660 RED Ball Bearing Turbocharger

    Appreciate the reply @ebatr24 , thanks! Dyno read a bit high at the very top, but based off of the fuel I usually get currently + what drob usually gets with the same setup I currently have a ballpark and basing the possible delta off of that
  14. **The Official FK8 Aftermarket Turbo Solutions and Technical Discussion Thread**

    Thanks for that @AlphaDigital . No plans for ethanol ATM, but not out of the question every now and then. Would probably need to get the flexfuel kit for that down the road if that becomes necessary. I'll probably end up getting injectors anyways, to leave the above as a possibility. EDIT...
  15. Turbo Upgrade - At What Point to Consider Injectors?

    Right, what CW_CTR said is correct. Sorry @Jason Baker was on a walk couldn't reply properly. XDI isn't the full system. Gonna assume it won't hurt, but probably due to pump gas will be greater diminishing returns? Not an expert, just based on the setups I've looked at! Just trying to learn...
  16. Turbo Upgrade - At What Point to Consider Injectors?

    Hi all, I've been flirting with the idea of upgrading my setup. Currently have the catalog of PRL bolt ons and a custom tune, but looking to go to RV6 R660 + XDI HPFP + PRL Race MAF(are there any other suggestions on race MAF?) I don't have access to ethanol here unfortunately, so just have...
  17. **The Official FK8 Aftermarket Turbo Solutions and Technical Discussion Thread**

    Hey everyone, Been looking into upgrading from the standard stock turbo / fuel / bolt-on setup to something new. Unfortunately I don't have access to E in my area, and am running 94 currently (Canada). What range of numbers can I expect? I'm most likely leaning towards the RV6 660 and at...
  18. RV6 R660 RED Ball Bearing Turbocharger

    Hey all with this turbo, Just doing some research.. Say I'm aiming for a modest ~450whp, is this attainable on pump (94 here where I am in Canada), XDI and stock injectors? At what point do you need to upgrade injectors? Race MAF? Drilled line? No intentions on adding E as it's not readily...
  19. 27WON FK8 Turbocharger Upgrade (The one the forum asked for)

    Anyone with this turbo + XDI HPFP (stock/xdi injectors)? Curious as to what you were able to put down.


Top